40–68 kHz precision ultrasonic cleaners for populated PCBs, SMT stencils, connectors and assemblies. DI-water compatible, with dryer options.
Samarth Electronics is an ISO 9001:2015 certified electronics ultrasonic cleaner manufacturer based in Ambarnath, Maharashtra, and a direct electronics ultrasonic cleaner supplier in Delhi NCR. As an established electronics ultrasonic cleaner exporter, we build the same equipment for buyers in the UAE, Saudi Arabia, Bangladesh, Nepal, Kenya, Nigeria and Sri Lanka. Customers in Delhi NCR get export-grade quality at factory-direct prices.
Electronics assembly needs precision cleaning that will not damage components. At 40–68 kHz the cavitation bubbles are small enough to reach under BGA packages, into fine-pitch connector cavities and between closely spaced leads, where spray nozzles and manual wiping cannot go.
In Delhi NCR, our electronics ultrasonic cleaner is used by electronics and mobile-phone manufacturers in Noida and Greater Noida; two-wheeler, car and tractor component plants in Gurugram, IMT Manesar, Faridabad and Bawal; and engineering units in Okhla, Faridabad and Sahibabad. Units are dispatched from our Ambarnath factory to Delhi NCR in transit-safe packing, with installation guidance, operator training and spares support.
Samarth Electronics electronics cleaners use SS 316L tanks with DI-water inlet and outlet, controlled 40–60 °C temperature to protect components and laminates, dedicated stencil holders and integrated hot-air dryers. They support IPC-7711/7721 cleaning procedures and ROSE ionic-contamination limits.
See the full product range on our Ultrasonic Cleaner for Electronic Industry page, or all equipment we supply in Delhi NCR.
Electronics and mobile-phone manufacturers in Noida and Greater Noida use it for populated PCBs, connectors and assemblies.
Two-wheeler, car and tractor component plants in Gurugram, IMT Manesar, Faridabad and Bawal use it for automotive electronics and sensor assemblies.
Engineering units in Okhla, Faridabad and Sahibabad use it for precision electro-mechanical parts.
Small bubbles clean under BGAs and fine-pitch leads safely.
SS 316L tank with DI inlet/outlet for an ion-free final rinse.
Avoids thermal stress on SMDs and PCB laminates.
Vertical stencil holders up to 736 × 736 mm.
Hot-air drying prevents moisture trapped under low-standoff parts.
Process records to support IPC cleanliness validation.
| Frequency | 40 kHz / 68 kHz |
| Tank sizes | 2 L bench-top to 50 L production |
| Chemistry | Aqueous flux remover / saponifier / DI water |
| Temperature | 40–60 °C |
| Stencil size | Up to 736 × 736 mm |
| DI water | SS 316L tank, DI inlet/outlet |
| Certification | IEC certified; IPC documentation available |
| Power supply | 230 V / 50 Hz; other voltages on request |
Specifications may vary by model and custom configuration. Confirm with our team before ordering.
| Requirement | Recommended | Notes |
|---|---|---|
| Repair / rework bench | 2–6 L bench-top, 40 kHz | Small parts and boards |
| EMS line, populated PCBs | 10–30 L, 40/68 kHz | DI rinse + dryer |
| SMT stencils | Stencil cleaner with holder | Up to 736 × 736 mm |
| High-volume assembly | Multi-stage wash–rinse–dry | SS 316L, DI water |
28–40 kHz for SMT stencils. 40–68 kHz for populated PCBs, because the smaller bubbles clean under BGAs and fine-pitch parts without stressing solder joints.
With the right frequency, power and chemistry it is safe for most SMDs. Quartz crystals and MEMS sensors may need shorter cycles, so test a sample board first.
DI water with an aqueous flux remover or saponifier for rosin flux, or a dedicated no-clean flux remover. Always finish with a DI rinse and full drying before test or conformal coating.
Yes. Integrated hot-air dryers prevent moisture being trapped under low-standoff components after cleaning.
Yes. Units are dispatched from our Ambarnath factory to Delhi NCR in transit-safe packing, with installation guidance, operator training and spares support. We cover New Delhi; Okhla; Gurugram; Udyog Vihar; IMT Manesar; and Faridabad and the surrounding areas.
Call or WhatsApp +91 9320240250 / +91 9322916496, email response@ultrasoniccleanersmfgr.com, or use our online enquiry form. Tell us your application, sample or part size and daily quantity, and we will send a quotation with the recommended model.
See all ultrasonic cleaners & lab equipment we supply in Delhi NCR »
Tell us your application, sample or part size and daily quantity. Our engineers will recommend the right model and send a factory-direct quotation.