Dedicated ultrasonic SMT stencil cleaner that restores blocked fine-pitch apertures in 5–8 minutes. Stencil holder, DI rinse and drying options.
Samarth Electronics is an ISO 9001:2015 certified SMT Stencil Cleaner manufacturer based in Ambarnath, Maharashtra, and a direct SMT Stencil Cleaner supplier in Pune. As an established SMT Stencil Cleaner exporter, we build the same equipment for buyers in the UAE, Saudi Arabia, Bangladesh, Nepal, Kenya, Nigeria and Sri Lanka. Customers in Pune get export-grade quality at factory-direct prices.
Every solder-paste stencil has to be cleaned before storage or reuse. Blocked apertures cause insufficient paste deposits, which lead to opens, tombstoning and BGA voids. Manual wiping with IPA takes 15–30 minutes per stencil and still leaves paste in apertures below 0.4 mm pitch.
In Pune, our SMT Stencil Cleaner is used by electrical and electronics makers in Pune's MIDC estates and aerospace and defence suppliers in Pune. Pune is a short road trip from our Ambarnath factory, so delivery, installation and service support are quick.
The Samarth Electronics ultrasonic stencil cleaner does the job in 5–8 minutes at 28–40 kHz. A purpose-built holder keeps the stencil vertical in the tank, so every aperture is cleaned evenly without frame distortion. A DI-water final rinse and hot-air drying complete the cycle, and the stencil is ready for the next print.
See the full product range on our Ultrasonic Stencil Cleaner page, or all equipment we supply in Pune.
Electrical and electronics makers in Pune's MIDC estates use it for SMT stencils on high-mix and high-volume lines.
Aerospace and defence suppliers in Pune use it for fine-pitch stencils for avionics boards.
Holds the stencil vertical for uniform cleaning without frame stress.
Cavitation reaches apertures as small as 0.3 mm.
Much faster than manual wiping, with more stencil turns per shift.
Leaves no ionic residue before the next print.
Operator-independent, repeatable cleaning.
Tanks for stencil frames up to 736 × 736 mm.
| Frequency | 28–40 kHz |
| Cycle time | 5–8 minutes typical |
| Cleaning temperature | 50–60 °C |
| Stencil size | Up to 736 × 736 mm frames |
| Fixture | Vertical stencil holder |
| Rinse | DI water rinse option |
| Drying | Hot-air dryer option |
| Power supply | 230 V / 50 Hz; other voltages on request |
Specifications may vary by model and custom configuration. Confirm with our team before ordering.
| Requirement | Recommended | Notes |
|---|---|---|
| Small EMS / prototype line | Single-tank stencil cleaner | Holder + timer |
| Production SMT line | Stencil cleaner + DI rinse | 5–8 min cycle |
| Multiple lines / large frames | Tank for 736 × 736 mm frames | Rinse + dryer |
| Stencils + misprints + pallets | Two-tank system | Separate wash and rinse |
Put the stencil in the holder, immerse it in warm stencil cleaner at 50–60 °C and 28–40 kHz for 5–8 minutes, rinse in DI water for 2 minutes, then air-dry. All apertures are clear for the next print.
Yes. The holder keeps the stencil vertical without frame stress, and controlled power clears apertures down to 0.3 mm without damage.
We build tanks for frames up to 736 × 736 mm. Tell us your frame size.
Yes. Misprinted bare boards, squeegee blades and pallets can be cleaned in the same system with suitable chemistry.
Yes. Pune is a short road trip from our Ambarnath factory, so delivery, installation and service support are quick. We cover Chakan; Talegaon; Bhosari; Pimpri-Chinchwad; Hinjewadi; and Ranjangaon and the surrounding areas.
Call or WhatsApp +91 9320240250 / +91 9322916496, email response@ultrasoniccleanersmfgr.com, or use our online enquiry form. Tell us your application, sample or part size and daily quantity, and we will send a quotation with the recommended model.
See all ultrasonic cleaners & lab equipment we supply in Pune »
Tell us your application, sample or part size and daily quantity. Our engineers will recommend the right model and send a factory-direct quotation.